Descrição
CONDIÇÃO: USADO
Estado de conservação: 9/10
Tecnicamente, a versão Mark II do pré-amplificador SP9 inclui um grupo de 14 melhorias diferentes, utilizando 61 componentes e mudanças de fios. Estes se combinam para fornecer maior confiabilidade e flexibilidade, além das melhorias sônicas.
– Na unidade de CD, o ganho foi reduzido em 12 dB, permitindo a operação do controle de ganho em sua rotação média ou alta, enquanto ainda deixa todas as outras entradas com ganho normal para fontes de programa de entrada mais baixas.
– O zumbido de baixo nível na seção de linha é reduzido de 10 a 20 dB, o que é perceptível principalmente em sistemas com alto-falantes de alta eficiência, pequenas salas “ao vivo”, amplificadores de potência de alto ganho ou fontes de programa de CD de baixo ruído.
Frequency response | High Level Section: ±.5dB, 5 Hz to 50 kHz, – 3dB points below 1 Hz and above 200kHz. |
---|---|
Phono: ±.3dB of RIAA, 30Hz to 40kHz. | |
Distortion (THD) | Less than 0.1% at 2V RMS output. (Typically less than 0.005% in midband) (SP-9: < .01% @ 2V RMS output 10Hz to 30kHz ) |
Noise & hum | High Level: (1) 70 µV RMS maximum residual unweighted wideband noise at main output with gain control minimum (98 dB below 5V RMS output). (2) More than 100dB below 1 V RMS input (less than 7µV equivalent input noise) (SP-9: Phono IHF weighted 72 dB below 1 mV input) |
Phono: 0.12 µV equivalent input noise; IHF weighted, shorted input (78dB below 1 mV input). | |
Gain | Phono input to tape output: 46dB |
Phono input to main output: 67dB (SP-9: Phono 66dB (RIAA ±.25 dB) | |
High level inputs to tape output: 0dB | |
High level inputs to main output: 21dB | |
CD input to main output: 9 dB | |
Input impedance | 50 k ohms line inputs |
47 K phono (Phono provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges) | |
Output impedance | 250 ohms main output |
850 ohms recorder output | |
Recommended load 60K ohms and 100pF. (20K ohms minimum) | |
Output polarity | |
Maximum inputs | Phono, 200 mv at 1kHz (1000 mv RMS, 10kHz) |
High level inputs essentially overload proof | |
Rated outputs | 2 V RMS 5 kHz to 50 kHz, all out-puts; 60k ohm load (main output capability is 50 V RMS output at 0.5% THD at 1 kHz into a 100K ohm load with 5V RMS high level input) |
Power supplies | Electronically–regulated low and high voltage supplies and electronic decoupling. Shielded toroid transformer. Line Regulation better than .01%. |
Tube complement | (2) 6922 |
Power requirements | 100-135 VAC 60 Hz (200-270 VAC 50/60Hz) 55 watts max |
Other | |
Dimensions | 19” (48 cm) W x 5 1/4” (13.4 cm) H (standard rack panel) x 10 ¼” (26 cm) D. Handles extend 1 ½” (3.8 cm) forward of the front panel. Rear chassis fittings extend 7/8” (2.3 cm). |
Weight | 12 lbs. (5.5 kg) Net; 21 lbs. (9.5 kg) Shipping |